• CCD Board Camera Black and white 
• 1/3" CCD; 420 TV Lines Resolution
• 0.1Lux
• 3.6mm / F2.0, 90 degree field of view
• 12 VDC @ 90 - 100mA
• Connector with Pre-tinned lead
• Array size 542 X 492
• 270,000 Pixels
• Auto-Shutter 1/60 to 1/100,000 Second
• Infrared sensitive
• PAL available
• Power supply not included

The CCD B/W cameras have optimal performance at 12VDC. Do not exceed 13 VDC under any circumstances. When wiring the cameras, it is strongly recommended that the power is turned off.

Many 12 Volt adapters have an extremely high open circuit voltage which means that an excessive voltage spike can damage the cameras. If you are uncertain about your power source, order the XF-200L. It provides 12 volts under load for this camera module.

The CNL-100 lens can be adjusted by rotating lens in either direction for proper focus. The spring adjustment makes the job easier by providing tension to lock the lens in place.  Some designs employ an easily removeable set-screw.

Pin hole lens design, CNP-101, can be adjusted if required by using the small Allen-head wrench and adjusting the set-screw located on the ridge, just below the lens. Do not over-tighten!  In some instances, a set-screw is not employed.  In this case, just rotate the lens to focus properly.
 

• CCD Board Camera Color 
• 1/4" CCD; 420 TV Lines Resolution
• 0.5 Lux
• 3.6mm / F2.0, 90 degree field of view
• Connector with Pre-tinned lead
• Operated by 12VDC 12 VDC @ 90 - 100mA regulated
• One board design
• Sony chip set
• Auto-Shutter 1/60 to 1/100,000 Second
• Infrared sensitive
• PAL available
• Power supply not included

The CCD color cameras have optimal performance at 12VDC. Do not exceed 13 VDC under any circumstances. When wiring the cameras, it is strongly recommended that the power is turned off.

Many 12 Volt adapters have an extremely high open circuit voltage which means that an excessive voltage spike can damage the cameras.  We recommend the use of a 12 volt regulated, XF-201-R (regulated) power supply for this module.

The CNL-100-C lens can be adjusted by rotating lens in either direction for proper focus. The spring adjustment makes the job easier by providing tension to lock the lens in place.  Some designs employ an easily removeable set-screw.

Pinhole lens design, CNP-101-C, can be adjusted if required by using the small Allen-head wrench and adjusting the set-screw located on the ridge, just below the lens. Do not over-tighten!  In some instances, a set-screw is not employed.  In this case, just rotate the pinhole lens to focus properly.
Note: -C for color version

• Size: 15 x 22mm
• Pixels: 365K(PAL), 250K(NTSC)
• Resolution: horizontal 380TV lines 
• Auto electronic exposure: 1/60 - 1/15000sec
• Automatic exposure/gain/white balance
• Min. illumination:<3 Lux at @f1.2
• S/N ratio: 48dB 
• Lens: f=3.6mm/F:2.0/92 degree view angle, (Pinhole f=5.5mm)
• Power supply: 9 VDC
• Power consumption: 40mA(max) 
• Power supply not included

• Size: 15 x 22mm
• Pixels: 365K(PAL), 250K(NTSC)
• Resolution: horizontal 380TV lines 
• Auto electronic exposure: 1/60 - 1/15000sec
• Automatic exposure/gain/white balance
• Min. illumination:<3 Lux at @f1.2
• S/N ratio: 48dB 
• Lens: f=3.6mm/F:2.0/92 degree view angle , (Pinhole f=5.5mm)
• Power supply: 9 VDC
• Power consumption: 40mA(max) 
• Power supply not included